4071_ifo
2.94 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
#!/bin/sh
#
# @name UVify IFO
#
# @type Quadrotor x
# @class Copter
#
# @output MAIN1 motor 1
# @output MAIN2 motor 2
# @output MAIN3 motor 3
# @output MAIN4 motor 4
#
# @maintainer Hyon Lim <lim@uvify.com>
#
# @board px4_fmu-v2 exclude
# @board px4_fmu-v3 exclude
# @board px4_fmu-v4pro exclude
# @board px4_fmu-v5 exclude
# @board px4_fmu-v5x exclude
# @board bitcraze_crazyflie exclude
# @board cuav_x7pro exclude
#
set VEHICLE_TYPE mc
set MIXER quad_x
set PWM_OUT 1234
# Attitude & rate gains
#param set MC_ROLL_P 7
param set-default MC_ROLLRATE_P 0.15
#param set MC_ROLLRATE_I 0.9
param set-default MC_ROLLRATE_D 0.0013
#param set MC_PITCH_P 7
param set-default MC_PITCHRATE_P 0.15
#param set MC_PITCHRATE_I 1.1
param set-default MC_PITCHRATE_D 0.0016
param set-default MC_YAW_P 2.8
param set-default MC_YAWRATE_P 0.2
#param set MC_YAWRATE_I 0.15
param set-default MC_YAWRATE_D 0
param set-default MC_YAW_FF 0.5
#param set MC_ROLL_TC 0.19
#param set MC_PITCH_TC 0.16
# Manual mode settings: Unleash Draco R's power :)
#param set MPC_MAN_TILT_MAX 70
#param set MC_PITCHRATE_MAX 1600
#param set MC_ROLLRATE_MAX 1600
#param set MC_YAWRATE_MAX 700
param set-default MPC_MANTHR_MAX 0.9
param set-default MPC_MANTHR_MIN 0.08
#param set MPC_MAN_TILT_MAX 35
#param set MPC_TILTMAX_AIR 20
# Filter settings
param set-default IMU_DGYRO_CUTOFF 90
param set-default IMU_GYRO_CUTOFF 100
# Thrust curve (avoids the need for TPA)
#param set THR_MDL_FAC 0.25
# System
param set-default PWM_MAIN_MAX 1950
param set-default PWM_MAIN_MIN 1100
param set-default PWM_MAIN_RATE 0
#param set SYS_FMU_TASK 1
param set-default SENS_BOARD_ROT 10
# EKF2
param set-default EKF2_GND_EFF_DZ 6
param set-default EKF2_HGT_MODE 1
# Position control
param set-default MPC_Z_P 1
param set-default MPC_Z_VEL_P_ACC 4
param set-default MPC_Z_VEL_I_ACC 0.4
param set-default MPC_THR_MIN 0.06
param set-default MPC_THR_HOVER 0.3
param set-default MIS_TAKEOFF_ALT 1.1
param set-default MPC_XY_P 1.7
param set-default MPC_XY_VEL_P_ACC 2.6
param set-default MPC_XY_VEL_I_ACC 1.2
param set-default MPC_XY_VEL_D_ACC 0.2
param set-default MPC_TKO_RAMP_T 1
param set-default MPC_TKO_SPEED 1.1
param set-default MPC_VEL_MANUAL 3
param set-default BAT_SOURCE 0
param set-default BAT_N_CELLS 4
param set-default BAT_V_DIV 10.14
param set-default BAT_A_PER_V 18.18
#param set CBRK_IO_SAFETY 22027
param set-default COM_DISARM_LAND 2
# Filter settings
param set-default IMU_GYRO_CUTOFF 90
param set-default IMU_DGYRO_CUTOFF 70
# Don't try to be intelligent on RC loss: just cut the motors
param set-default NAV_RCL_ACT 6
# enable to use high-rate logging for better rate tracking analysis
# param set SDLOG_PROFILE 19
# TELEM1 ttyS1 - Wifi module
param set-default MAV_0_CONFIG 101
param set-default MAV_0_RATE 0
# onboard
param set-default MAV_0_MODE 2
param set-default SER_TEL1_BAUD 921600
# TELEM2 ttyS2 - Sub 1-Ghz
param set-default MAV_1_CONFIG 102
# normal
param set-default MAV_1_MODE 0
param set-default SER_TEL2_BAUD 57600