4073_ifo-s
3.27 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
#!/bin/sh
#
# @name UVify IFO
#
# @type Quadrotor x
# @class Copter
#
# @output MAIN1 motor 1
# @output MAIN2 motor 2
# @output MAIN3 motor 3
# @output MAIN4 motor 4
#
# @board px4_fmu-v2 exclude
# @board px4_fmu-v3 exclude
# @board px4_fmu-v4pro exclude
# @board px4_fmu-v5 exclude
# @board px4_fmu-v5x exclude
# @board bitcraze_crazyflie exclude
# @board cuav_x7pro exclude
#
# @maintainer Hyon Lim <lim@uvify.com>
#
set VEHICLE_TYPE mc
set MIXER quad_x
set PWM_OUT 1234
# Attitude & rate gains
#param set MC_ROLL_P 7
param set-default MC_ROLLRATE_P 0.15
#param set MC_ROLLRATE_I 0.9
param set-default MC_ROLLRATE_D 0.0013
#param set MC_PITCH_P 7
param set-default MC_PITCHRATE_P 0.15
#param set MC_PITCHRATE_I 1.1
param set-default MC_PITCHRATE_D 0.0016
param set-default MC_YAW_P 2.8
param set-default MC_YAWRATE_P 0.2
#param set MC_YAWRATE_I 0.15
param set-default MC_YAWRATE_D 0
#param set MC_ROLL_TC 0.19
#param set MC_PITCH_TC 0.16
# Manual mode settings: Unleash Draco R's power :)
#param set MPC_MAN_TILT_MAX 70
#param set MC_PITCHRATE_MAX 1600
#param set MC_ROLLRATE_MAX 1600
#param set MC_YAWRATE_MAX 700
param set-default MPC_MANTHR_MIN 0.08
#param set MPC_MAN_TILT_MAX 35
#param set MPC_TILTMAX_AIR 20
# Filter settings
param set-default IMU_GYRO_CUTOFF 100
# Thrust curve (avoids the need for TPA)
#param set THR_MDL_FAC 0.25
# Obsolete
#param set PWM_MAIN_MAX 1950
#param set PWM_MAIN_MIN 1100
#param set PWM_MAIN_RATE 0
# Sensors
param set-default SENS_BOARD_ROT 10
# Yaw 180
param set-default SENS_FLOW_ROT 4
# TFMini on TELEM3
param set-default SENS_TFMINI_CFG 103
# Smart Battery
param set-default SENS_EN_BATT 1
# EKF2
param set-default EKF2_AID_MASK 3
param set-default EKF2_GND_EFF_DZ 6
param set-default EKF2_HGT_MODE 1
param set-default EKF2_MIN_RNG 0.3
param set-default EKF2_RNG_AID 1
# Flow
param set-default EKF2_OF_QMIN 70
# Position control
param set-default MPC_Z_P 1.1
param set-default MPC_Z_VEL_P_ACC 6
param set-default MPC_Z_VEL_I_ACC 1
param set-default MPC_THR_MIN 0.06
param set-default MPC_THR_HOVER 0.44
param set-default MIS_TAKEOFF_ALT 1.1
param set-default MPC_XY_P 1.7
param set-default MPC_XY_VEL_P_ACC 2.6
param set-default MPC_XY_VEL_I_ACC 1.2
param set-default MPC_XY_VEL_D_ACC 0.2
param set-default MPC_TKO_RAMP_T 1
param set-default MPC_TKO_SPEED 1.1
param set-default MPC_VEL_MANUAL 3
param set-default BAT_SOURCE 0
param set-default BAT_N_CELLS 4
param set-default BAT_V_DIV 10.14
param set-default BAT_A_PER_V 18.18
#param set CBRK_IO_SAFETY 22027
param set-default COM_DISARM_LAND 2
# Filter settings
param set-default IMU_GYRO_CUTOFF 90
# Don't try to be intelligent on RC loss: just cut the motors
param set-default NAV_RCL_ACT 6
# enable to use high-rate logging for better rate tracking analysis
# param set SDLOG_PROFILE 19
# TELEM1 ttyS1 - Wifi module
param set-default MAV_0_CONFIG 101
param set-default MAV_0_RATE 0
# onboard
param set-default MAV_0_MODE 2
param set-default SER_TEL1_BAUD 921600
# TELEM2 ttyS2 - Sub 1-Ghz
param set-default MAV_1_CONFIG 102
# normal
param set-default MAV_1_MODE 0
param set-default SER_TEL2_BAUD 57600
# DSHOT
param set-default DSHOT_CONFIG 600
# EKF OF POSITION
param set-default EKF2_OF_POS_X 0.06
param set-default EKF2_OF_POS_Y 0.03
param set-default EKF2_OF_POS_Z -0.07
# Failsafe
param set-default COM_LOW_BAT_ACT 3