4072_draco
2.26 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
#!/bin/sh
#
# @name UVify Draco
#
# @type Quadrotor x
# @class Copter
#
# @output MAIN1 motor 1
# @output MAIN2 motor 2
# @output MAIN3 motor 3
# @output MAIN4 motor 4
#
# @maintainer Hyon Lim <lim@uvify.com>
#
# @board px4_fmu-v2 exclude
# @board px4_fmu-v3 exclude
# @board px4_fmu-v4pro exclude
# @board px4_fmu-v5 exclude
# @board px4_fmu-v5x exclude
# @board bitcraze_crazyflie exclude
#
. ${R}etc/init.d/rc.mc_defaults
set MIXER quad_x
set PWM_OUT 1234
# use the Q attitude estimator, it works w/o mag or GPS.
param set-default SYS_MC_EST_GROUP 3
param set-default ATT_ACC_COMP 0
param set-default ATT_W_ACC 0.4
param set-default ATT_W_GYRO_BIAS 0
param set-default SYS_HAS_MAG 0
# Attitude & rate gains
param set-default MC_ROLL_P 8.0
param set-default MC_ROLLRATE_P 0.11
param set-default MC_ROLLRATE_I 0.3
param set-default MC_ROLLRATE_D 0.0015
param set-default MC_ROLLRATE_MAX 1600
param set-default MC_PITCH_P 8
param set-default MC_PITCHRATE_P 0.13
param set-default MC_PITCHRATE_I 0.35
param set-default MC_PITCHRATE_D 0.0015
param set-default MC_PITCHRATE_MAX 1600
param set-default MC_YAW_P 4
param set-default MC_YAWRATE_P 0.21
param set-default MC_YAWRATE_I 0.3
param set-default MC_YAWRATE_D 0.0
param set-default MC_YAW_FF 0.5
param set-default MC_YAWRATE_MAX 600
param set-default MC_ROLL_TC 0.19
param set-default MC_PITCH_TC 0.16
param set-default MC_AIRMODE 1
param set-default MPC_MAN_TILT_MAX 60
param set-default MPC_THR_CURVE 1
param set-default MPC_THR_HOVER 0.25
# Thrust curve (avoids the need for TPA)
param set-default THR_MDL_FAC 0.3
# System
param set-default PWM_MAIN_MAX 1950
param set-default PWM_MAIN_MIN 1180
# enable one-shot
param set-default PWM_MAIN_RATE 0
param set-default SENS_BOARD_ROT 2
param set-default BAT_SOURCE 0
param set-default CBRK_IO_SAFETY 22027
#param set COM_DISARM_LAND 3
# Filter settings
param set-default IMU_GYRO_CUTOFF 90
param set-default IMU_DGYRO_CUTOFF 100
# Don't try to be intelligent on RC loss: just cut the motors
#param set NAV_RCL_ACT 6
# enable to use high-rate logging for better rate tracking analysis
param set-default SDLOG_PROFILE 27
# TELEM1 ttyS1
#param set MAV_0_CONFIG 101
#param set MAV_0_MODE 2 # onboard
#param set MAV_0_RATE 20000
#param set SER_TEL1_BAUD 921600
# TELEM2 ttyS2
#param set MAV_1_CONFIG 0